The first thing you’ll need is a set of metal building blocks.
You’ll need to make a couple of little steel plates and then you’ll also need to drill holes for the blocks.
The first step is to make the blocks, which is a bit more involved than it sounds.
You can either use the same drill bit you used to make steel plates to make small steel plates that you can then drill into.
The idea is that the metal plates will hold together better than your ordinary flat bit, so you can make smaller holes in the steel plate instead of a huge hole in the sheet metal.
Then, you can either make the holes yourself or buy a set from a hobby shop.
The hobby shop I went to had a huge variety of different sizes of blocks available, so I opted for the bigger block, which was a couple feet across and two inches thick.
I chose the thickest, which measured about one foot across.
You’ll also want to use a bit of sandpaper to clean the blocks after they’ve been drilled.
The sandpaper is essential for this step.
If you have a router, you’ll want to get a sanding block to make sure that the blocks are evenly distributed and are evenly spaced.
If you don’t have a sandpaper, you may want to sand your blocks a bit smaller and the holes a bit larger.
Then, you need to lay them out on a flat surface.
If all of that sounds complicated, that’s because it is.
I mean, you’re just building a piece of steel and you’re trying to get the pieces to be equally spaced and evenly spaced, right?
You need to find a nice, solid base.
If this isn’t a big deal to you, you could just make the base from a sheet of wood, and you can also do that if you have some metal rods to make your pieces.
This will also work, if you use some aluminum.
The trick is that you’re going to have to drill a hole in a piece that’s a little bit bigger than the diameter of the rod.
Once you’ve found the base, you want to make some holes in it that will be wide enough to allow the blocks to pass through.
You can do this by drilling a hole that’s about half a foot wide on one side and about half another on the other.
The next step is the drilling of the holes.
The drill bit will probably need a bit to get it right, but I found that by drilling just one small hole in one of the blocks and then gently pushing it back into place, I got it right.
Once it’s in place, you simply drill a smaller hole in it, and that will keep the holes in place and allow the block to pass.
I also found that it was easier to drill in a slightly smaller hole, so if you’re drilling a big hole, I would recommend doing that first.
I found it a bit easier to get them to fit the holes that I drilled, so it’s a bit less work to do it with just one hole.
The final step is cutting the blocks into pieces.
You’re going be cutting them into different shapes, so each one will need to be shaped exactly the same way.
I drilled a couple small holes in one block, then drilled a few more in the other, then gently pushed the block into place and drilled a small hole to allow for the pieces.
I ended up with about six pieces of wood for the first one, which were about an inch wide.
The other blocks were about one-third that width.
I used a hacksaw to cut the blocks from the wood that I had, then I sanded them with a bit and then sanded again and sanded the other blocks.
After I sand them, I drilled a hole through the middle of each one and cut out the pieces with a little sandpaper.
Then I glued the pieces together using my favorite glue, which I use for everything.
The glue that I used is called polyurethane.
It’s made from a mixture of polyvinyl chloride (PVC), vegetable oil and aluminum oxide.
It can be purchased at most hardware stores.
It is very easy to use, so once you get the hang of it, you don’ need to do anything else.
It won’t be very long before you’re done.
After the blocks have been glued together, I cut out a piece from the center of the block, and I then attached that piece to the other block using a bit.
Then I attached that bit to the first block, so the two blocks now look like this:You can use this as a template for how you’ll make your building pieces.
For this one, I did this by making a rectangle about three feet wide, with the edges cut out of the wood.
Then for this one I used the same pattern, and for the other one, the same rectangle, but this time I made a triangle about three inches wide and a rectangle that was about two inches tall